Optical Heat Absorbing Glass Grb1 Kg2 Kg5 Shortpass Filters

Heat absorbing glass filter is used to reduce heat transfer from the optical system. Heat absorbing glass filters high transmission in the visible wavelength region and absorption in the infrared wavelength region.

What is Heat Absorbing Filters?

Heat Absorbing Filters feature high transmittance in the visible region and good absorption of heat
rays (infrared rays). They efficiently absorb thermal radiation emitted from light sources and are
highly effective when employed for slide projectors and illumination equipment.

Performance of Heat Absorbing Filters

Heat-absorbing filters in lighting systems get hot during operation. The heat is efficiently dissipated from an optical system by directly cooling or by ventilation of the absorbing filter glass. We recommend the filters’ thermal tempering after the polishing and shaping processes whenever heat-absorbing glass must withstand an increased operating temperature.

Application of KG-Filters

KG-Filters not only work in lighting applications. Many other optical systems profit from the exciting properties of these standard SCHOTT glass filter materials. As the KG-absorption glasses have the advantage of a much more broadband blocking of the infrared wavelength range than coated filters (Hot Mirrors), they represent a better solution whenever you want to block a broad IR spectrum.

Optics Custom Optical Heat Absorbing Glass photo display

Specifications of optical Kg5 Optical Shortpass Filters

Curves for Schott KG Series Heat Absorbing Glass

Term of Optical Filter 

CENTRAL WAVELENGTH

Center Wavelength (CWL), used in defining bandpass filters, describes the midpoint of spectral bandwidth over which the filter transmits. Traditional Coated Optical Filters tend to achieve a maximum transmission near the center wavelength, whereas Hard Coated Optical Filters tend to have a fairly flat transmission profile over the spectral bandwidth. 

BANDWIDTH

Bandwidth is a wavelength range used to denote a specific part of the spectrum that passes incident energy through filters.
Bandwidth is also referred to as FWHM (Figure 1). 

FIGURE 1: ILLUSTRATION OF CENTER WAVELENGTH AND FULL WIDTH AT HALF MAXIMUM

FULL WIDTH-HALF MAXIMUM

Full Width-Half Maximum (FWHM) describes the spectral bandwidth over which a bandpass filter will transmit. The upper and lower limit of that bandwidth is defined at the wavelengths where the filter achieves 50% of the maximum transmission. For example, if the maximum transmission of the filter is 90%, the wavelengths at which the filter achieves 45% transmission will define the upper and lower limits of the FWHM. FWHM’s of 10nm or less are considered narrow band and often used for laser clean-up and chemical detection. FWHM’s of 25 – 50nm are often used in machine vision applications; FHWM’s of more than 50nm are considered broadband and typically used in fluorescence microscopy applications. 

BLOCKING RANGE

Blocking Range is wavelength interval used to denote a spectral region of energy that is attenuated by the filter (Figure 2).
The degree of its blocking is typically specified in terms of optical density.

FIGURE 2: ILLUSTRATION OF BLOCKING RANGE

SLOPE

Slope is a specification often defined on edge filters, such as short pass or long pass filters, to describe the bandwidth over which the filter transitions from high blocking to high transmission. Given as the percent of the cut-wavelength, slope can be specified from a variety of starting and end points. 

OPTICAL DENSITY

Optical Density (FIGURE 3) describes the amount of energy blocked or rejected by a filter. A high optical density value indicates low transmission, and low optical density indicates high transmission. Optical densities of 6 or greater are used for extreme blocking needs such as Raman spectroscopy or fluorescence microscopy. Optical densities of 3.0 – 4.0 are ideal for laser separation and clean-up, machine vision, and chemical detection, while optical densities of 2.0 or less are ideal for color sorting and separating spectral orders. 

FIGURE 3: ILLUSTRATION OF OPTICAL DENSITY

CUT-ON WAVELENGTH

Cut-On Wavelength is a term used to denote the wavelength at which the transmission increases to 50% throughput in a long pass filter.
Cut-on wavelength is indicated by λ cut-on in Figure 4.

FIGURE 4: ILLUSTRATION OF CUT-ON WAVELENGTH

CUT-OFF WAVELENGTH

Cut-Off Wavelength is a term used to denote the wavelength at which the transmission decreases to 50% throughput in a short pass filter.
Cut-off wavelength is indicated by λ cut-off in Figure 5.

FIGURE 5: ILLUSTRATION OF CUT-OFF WAVELENGTH

People also ask

• Is bandpass filter better than low pass filter?
  Unlike the low pass filter which only pass signals of a low frequency range or the high pass filter which pass signals of a higher frequency range, a Band Pass Filters passes signals within
  a certain “band” or “spread” of frequencies without distorting the input signal or introducing extra noise.
   
• What is bandpass vs notch filter?
  The main difference between a bandpass filter and notch filter is that bandpass filter allows signals within a particular frequency range to pass and a notch filter will filter those signals out in that one frequency range.
   
• What is the difference between bandpass filter and low pass filter?
  A bandpass filter allows signals between two specific frequencies to pass, but that discriminates against signals at certain frequencies. A low pass filter is a filter that passes signals with a frequency lower than a certain cutoff frequency and minimizes signals with frequencies higher than the cutoff.
   
• What does an optical filter do?
  Optical filters are passive optical devices that consist of specialized optical coatings applied onto a substrate. The coatings modify the refractive index of the substrate, enabling them to reflect, transmit, or absorb incoming light depending on its wavelength.